Plastic Molding Tolerances: Material and Size Lookup

Compare stored dimensional references for 17 plastic material families, nominal size and three precision selections. The original standard, edition and complete transcription audit are not recorded in this legacy dataset. Use it for design review while confirming the drawing requirement and dimension classification; it does not establish manufacturing capability.

Look up a material and size

Stored size range: greater than 0 to 1600 mm (about 62.992126 in). Precision selection maps to a material-specific grade. Unit changes preserve the nominal dimension and clear the old result; calculate again to create a new snapshot.

How do you read a plastic molding tolerance?

A dimensional tolerance specifies the permitted variation of a nominal size. For a symmetric result ±t, the lower deviation is −t, the upper deviation is +t, and the full tolerance band is 2t. The size limits are nominal −t and nominal +t. A reference value cannot by itself demonstrate the variation a particular molding process will achieve.

QuantityMeaning50 mm, reference A example
Symmetric deviation±t around nominal±0.055 mm
Lower / upper deviationSigned offsets, not finished sizes−0.055 / +0.055 mm
Total bandUpper minus lower deviation: 2t0.110 mm
Size limitsNominal plus each signed deviation49.945 to 50.055 mm

Nominal size, deviations and full band

A nominal dimension n has lower limit n minus t, upper limit n plus t, and full band two tNominal feature dimension nn − tnn + tFull tolerance band 2t

Enter the nominal finished-part dimension being reviewed. This diagram explains symmetric size limits, not mold-parting-line behavior. Reference A and B retain the previous “fixed half” and “movable half” labels for traceability; the original dimension definitions have not been verified. Do not select a reference solely from which half of the mold moves.

Plastic molding tolerance examples by material and size

These three cases use the same stored data and calculation model as the interactive lookup and API. They verify software arithmetic, not a complete standard transcription or a supplier’s production capability. All values below are in millimetres.

Material / nominal / selectionStored gradeReference A: ± deviation; full band; limitsReference B: ± deviation; full band; limits
ABS / 50 mm / High precision3±0.055 mm;
band 0.11 mm;
49.945 to 50.055 mm
±0.075 mm;
band 0.15 mm;
49.925 to 50.075 mm
PP / 100 mm / General precision7±0.3 mm;
band 0.6 mm;
99.7 to 100.3 mm
±0.35 mm;
band 0.7 mm;
99.65 to 100.35 mm
LDPE / 20 mm / Low precision10±0.44 mm;
band 0.88 mm;
19.56 to 20.44 mm
±0.54 mm;
band 1.08 mm;
19.46 to 20.54 mm

What are typical injection molding tolerances?

There is no single tolerance for every injection-molded plastic part. Review material, nominal size, feature definition and the applicable drawing standard. In this legacy dataset, reference A gives ±0.055 mm for ABS at 50 mm/high precision, ±0.300 mm for PP at 100 mm/general precision, and ±0.440 mm for LDPE at 20 mm/low precision. Those are different input conditions, not universal material capability limits or interchangeable grades.

A bare number such as 0.01 is incomplete without a unit and tolerance definition: 0.01 inch equals 0.254 mm. Whether a requirement is suitable depends on the actual feature and production evidence. This lookup does not calculate geometric defects, assembly stack-up or a capability index.

Shrinkage reference is separate from dimensional tolerance

The shrinkage range displayed for each material is stored reference text. It is not a part-specific shrink-compensation calculation and is not added to the tolerance band. Exact resin grade, filler, conditioning, geometry and processing conditions still need review. The tool offers material-family and precision mappings; it does not simulate mold design, cooling, warpage or process settings.

Turn a lookup into a manufacturing requirement

  1. Identify the critical finished-part dimension, its units and inspection method. Agree the drawing standard and correct feature classification.
  2. Confirm resin grade, fillers, conditioning, geometry and tooling with the manufacturer. Review tight dimensions and whether tool changes, process development or a secondary operation are appropriate.
  3. Use measured samples and cavity/lot variation to assess actual process capability. A permissible tolerance defines an acceptance requirement; process capability describes observed production behavior. One does not automatically guarantee the other.

Sources, scope and maintenance

The numeric references and material-to-grade mappings are retained from CPF’s existing plastic-molding dataset. Its original standard, edition, import provenance and complete transcription audit are not recorded. Reference A uses half the stored band. Reference B preserves the existing grade-based full-band allowance before halving: 0.02 mm for grades 1–2, 0.04 mm for 3–4, 0.10 mm for 5–7, and 0.20 mm for 8–10. The applicability of the legacy mold-half labels still requires source confirmation.

Stored intervals use > lower to ≤ upper bounds. This revision preserves the numeric tables while correcting unit-rounding drift, input validation and result snapshots. It does not certify GB/T 14486, ISO 20457, DIN 16742, every plastic process or newer standard editions. A named independent engineering reviewer is not recorded. Model CPF-plastic-molding-2026-11-10; revised November 10, 2026.