Sheet Metal Tolerance Calculator

Look up blanking, bending, shearing and general dimensional or geometric references. Use the feature length, applicable thickness and drawing class. The represented JIS references are associated with 1991 editions in the technical excerpt linked below; laser and hole references have unconfirmed sources. This tool does not verify ISO conformity or shop capability.

Choose a reference

The all-reference view reuses one entered size for different feature lengths. Use separate runs when your cut width, formed dimension, shorter side or evaluation length differs. Grade A/B are legacy data presets: they are not universal JIS classes. Laser/hole references ignore the grade preset; their source is unconfirmed.

What are sheet metal tolerances?

Sheet metal tolerance is the permitted variation of a specified feature. A symmetric dimensional tolerance ±t allows a size from nominal −t to nominal +t; its total band is 2t. A straightness, flatness or perpendicularity value describes an unsigned geometric zone, not ± a size deviation. Neither output establishes the manufacturer’s observed process capability.

A flat cut dimension and a formed dimension across bends need different review. Specify the feature, datum, material, thickness, drawing standard and class. This calculator does not calculate bend angles, bend allowance, cumulative stack-up or raw-stock thickness tolerances.

Which dimension should you enter?

Use cut width for a sheared-width lookup, the shorter side for perpendicularity, and evaluation length for straightness/flatness. The all-reference view shares one number across these different lengths; use separate runs if the actual feature lengths differ. Sheet thickness is an input to the applicable table, not its calculated output.

Flat feature distance, formed dimension and geometric evaluation length require separate inputsFlat dimension / cut widthFormed dimensionEvaluation length / zone

The diagram explains input meaning. It is not a bend-to-bend error model or a supplier tolerance guarantee.

References, inputs and output meaning

ReferenceInput length / thicknessOutput
Blanking by press working
JIS B 0408; reference excerpt 1991
Blanked linear dimension± deviation; total band and size limits
Bending / drawing dimensions
JIS B 0408; reference excerpt 1991
Formed linear dimension, not bend angle± deviation; total band and size limits
Sheared cut width
JIS B 0410; reference excerpt 1991
Cut width; sheet thickness also required± deviation; total band and size limits
Sheared straightness
JIS B 0410; reference excerpt 1991
Evaluation length; sheet thickness also requiredUnsigned zone width; no nominal-size limits
Sheared perpendicularity
JIS B 0410; reference excerpt 1991
Shorter-side length; sheet thickness also requiredUnsigned zone width; no nominal-size limits
Other linear dimensions
JIS B 0405; reference excerpt 1991
Linear dimension excluding chamfers± deviation; total band and size limits
General perpendicularity
JIS B 0419-1991
Shorter-side lengthUnsigned zone width; no nominal-size limits
General straightness / flatness
JIS B 0419-1991
Evaluation lengthUnsigned zone width; no nominal-size limits
Laser-cutting reference
Legacy CPF reference; standard/source unrecorded
Stored nominal size; sheet thickness also required± deviation; total band and size limits
Legacy hole reference
Legacy CPF reference; size definition/source unconfirmed
Stored reference size; definition requires review; sheet thickness also required± deviation; total band and size limits

Stored A/B correspond to A/B for blanking, bending and shearing; f/m for the represented B 0405 linear entries; H/K for B 0419 perpendicularity and straightness/flatness. Other classes are not offered. The mappings were checked against the MISUMI technical excerpt; this is not a complete licensed-standard transcription audit. Laser/hole references are separate legacy data, ignore A/B, and require source review before acceptance.

Reproducible sheet metal reference examples

These examples use the same model and stored files as the calculator. They demonstrate model behavior and arithmetic, not production capability.

100 mm — Blanking by press working

Class Grade A; result ±0.15 mm. Lower deviation -0.15 mm, upper +0.15 mm; total band 0.3 mm; size limits 99.85–100.15 mm.

Recalculate this example

250 mm — Bending / drawing dimensions

Class Grade B; result ±1.2 mm. Lower deviation -1.2 mm, upper +1.2 mm; total band 2.4 mm; size limits 248.8–251.2 mm.

Recalculate this example

100 mm — General straightness / flatness

Class H (stored A); result 0.1 mm. This is an unsigned zone, not a symmetric size deviation.

Recalculate this example

120 mm — Sheared cut width

Class Grade A; thickness 3 mm; result ±0.3 mm. Lower deviation -0.3 mm, upper +0.3 mm; total band 0.6 mm; size limits 119.7–120.3 mm.

Recalculate this example

What is the typical flatness tolerance for sheet metal?

There is no single flatness value that applies to every sheet-metal part. Use the drawing’s standard, class and evaluation length. In this stored general reference, a 100 mm evaluation length with H (stored A) gives a 0.1 mm unsigned zone. A different length or class can give another value. Raw-sheet flatness, formed-part flatness and measured shop capability must be reviewed under their own conditions.

When should manufacturing review the requirement?

  1. Identify critical features and datums on the finished part, including functional dimensions across bends.
  2. Review material, thickness, bend geometry, tooling and any assembly stack. This lookup cannot add individual tolerances into a verified assembly fit.
  3. For tight dimensions, agree the inspection method, uncertainty and production conditions. Ask for actual measurement/capability evidence before treating a reference value as a production commitment.

Sources and maintenance

Numeric source: CPF’s existing public/data/bjgc/table1–10.json files. Five sheared-width entries for thickness >6 to ≤12 mm were reassigned from stored A to B after comparison with the technical excerpt; reference magnitudes were retained. The MISUMI technical excerpt identifies JIS B 0408, B 0410, B 0405 and B 0419 (1991) and was checked for represented class mappings, feature terminology and examples. Original CPF import provenance, a complete transcription audit and a named engineering reviewer are not recorded. Laser/hole sources and the legacy hole size definition remain unconfirmed; do not use them for acceptance without a reviewed drawing/source.

Stored intervals use > lower to ≤ upper bounds. A null upper bound is unconfirmed, not automatically unlimited. Blank or absent entries remain not tabulated. This tool does not claim all standard classes, ISO coverage or newer editions. Model CPF-sheet-metal-2026-11-08; revised November 8, 2026.