DIE FORGING · DIMENSIONAL REFERENCE

Aluminum forging tolerances: L, H and size limits

Aluminum forging tolerance is the permitted variation of a specified dimension. For this lookup, choose L within one die half, or H across the parting plane plus the projected area. Read the upper and lower deviations separately: an asymmetric band is not a ± value.

Standard status: GB/T 8545-2012 was replaced by GB/T 8545-2024 on 1 October 2024. The retained tables below are historical reference data associated with the 2012 edition; they have not been fully audited against the official text or verified to the 2024 edition. Confirm the drawing’s agreed standard and edition before use for acceptance.

Aluminum forging tolerance calculator

Historical A/B lookup for L or H + projected area. These retained tables are associated with GB/T 8545-2012; they are not verified to the replacing 2024 edition.

Unit switches convert the entered value without display rounding. For H, enter the forging’s projected area viewed along the forging direction, not a surface area. 1 cm² = 100 mm²; 1 in² = 6.4516 cm².

Which dimensions and area should I enter?

Single-die dimension L, cross-die dimension H and projected areaA forging spans upper and lower die halves. L has both endpoints in the upper half. H crosses the horizontal parting plane. A separate plan view marks the projected outline perpendicular to the forging direction.LHDashed line: parting planeForgingdirectionAProjected outline
Original schematic, not a standard drawing. The projection is viewed along the forging direction; the parting-plane geometry must be established from the actual tooling.
Parameter and coverage guide
InputMeaning / stored coverage
Non-cross dimension LBoth endpoints are defined in one die half, without crossing the parting plane. Stored sizes: positive L up to 6300 mm.
Cross dimension HDimension spanning the die halves, influenced by die closure. Stored sizes: positive H up to 1250 mm.
Projected area AForging outline projected along the forging direction. Enter cm² or in², up to 22000 cm². It is not the total 3D surface area.
Grades A and BOriginal dataset grade labels. Coverage is sparse: an absent cell is unavailable, not zero or a license to interpolate.
Interval endpointsEach > lower endpoint is excluded; each upper endpoint is included. Decimal unit conversion retains precision.

Three reproducible table examples

These are software results from the retained dataset, not independent validation of the standard or a production capability test. All example dimensions below are in mm.

L = 18 mm, within one die half

The upper endpoint 18 mm stays in the >10–18 mm row. Grade B allows −0.3 to +0.6 mm: 17.7–18.6 mm, total width 0.9 mm. It is not ±0.6 mm.

Size row: >10.0~18.0 mm.

Grade B · mm
Upper deviation+0.6
Lower deviation-0.3
Total tolerance width0.9
Lower size limit17.7
Upper size limit18.6
Grade A · mm
Upper deviation+0.3
Lower deviation-0.3
Total tolerance width0.6
Lower size limit17.7
Upper size limit18.3
Recalculate this example →

H = 18 mm, projected area = 100 cm²

Both inputs select a cell: H in >10–18 mm and area in >50–100 cm². Changing area can change the deviation without changing H.

Size row: >10.0~18.0 mm; area: >50 ~100 cm².

Grade B · mm
Upper deviation+0.9
Lower deviation-0.6
Total tolerance width1.5
Lower size limit17.4
Upper size limit18.9
Grade A · mm
Upper deviation+0.6
Lower deviation-0.4
Total tolerance width1
Lower size limit17.6
Upper size limit18.6
Recalculate this example →

L = 120 mm, within one die half

A second length example illustrates that A/B are stored table grades, not a guaranteed capability ranking for a supplier.

Size row: >80.0~120.0 mm.

Grade B · mm
Upper deviation+1.2
Lower deviation-0.8
Total tolerance width2
Lower size limit119.2
Upper size limit121.2
Grade A · mm
Upper deviation+0.7
Lower deviation-0.7
Total tolerance width1.4
Lower size limit119.3
Upper size limit120.7
Recalculate this example →

What the tolerance means for manufacturing

  1. Establish the feature and edition. Identify the actual parting plane, whether the feature is L or H, and the standard edition on the drawing. Aluminum and steel forging standards are not interchangeable.
  2. Check the entire signed band. Upper size = nominal + upper deviation; lower size = nominal + lower deviation. For +0.6/−0.3 mm the full width is 0.9 mm. Do not halve it and recenter it on nominal.
  3. Separate forging stock from finished sizes. A machining allowance is intentionally retained stock. It is not the tolerance width. Critical fits, threads and sealing faces may need finish machining with separately specified limits.
  4. Agree inspection and capability. This table does not calculate die-cavity shrinkage compensation, mismatch, draft, roughness, mechanical properties, Cpk or supplier capability. Confirm those independently with the supplier and the drawing.

Sources, edition status and maintenance

  • SAMR: GB/T 8545-2012 status record identifies the historical dimensional-deviation and machining-allowance standard and its replacement.
  • SAMR: GB/T 8545-2024, Aluminium alloy forgings records implementation on 1 October 2024 and full replacement of the 2012 edition. This calculator has not been updated to claim its table coverage.
  • The software uses three unchanged local files: L table, H grade B and H grade A. The original transcription and every numerical cell have not been independently audited; incomplete cells retain their missing-value meaning.

Software, unit boundaries and standard-status references reviewed 14 November 2026. No named independent standards reviewer has been recorded. Confirm an official licensed standard and contract requirements before production use.